In this Category

Urethane Bushings -- where Road meets Chassis.


CV-2 Suspension and Axle Grease

Price: $13.99

*Free Shipping in the USA For Orders Over $99!

Please choose

Urethane suspension bushings have a reputation for squeaking. While the design and compound of the urethane itself can sometimes be to blame, many times it is the fact that improper grease has been used. Certain types of greases do not have the correct properties to stay in place and/or have the tendency to emulsify with water. When grease emulsifies with water, its properties change and it thins out and runs/squishes out from the bushing which eventually leads to squeaking.

We have found the CV-2 grease to have properties that work perfectly with urethane bushings. CV-2 has a very high water-washout resistance and withstands very high pressures. Combine that with the fact that CV-2 is tacky enough and thick enough stay put within the bushings and you have a grease that has all the correct properties to provide your urethane bushings with many years and many thousands of miles of noise free service.

 

  • Outperforms the best conventional or synthetic greases and lubes
  • Withstands extreme temperature and pressure in wheel bearings, U-joints, and high-angle CV Joints
  • Excellent high-temp stability, extreme-pressure protection, and water resistance
  • Used in a variety of applications with operating temps from -100°F to 500°F
  • Strong resistance to oxidation and corrosion, low evaporation and oil separation with a minimum effect on rubber seals
  • Contains an organic moly for chassis lubrication
  • Synthetic fluidity allows increases in bearing life up to 200%
  • Will darken after high-temp use-not detrimental to performance
  • Highly resistant to water washout
  • Perfect for use with Powerflex urethane suspension bushings for long life and to prevent squeaking

PROPERTY CV-2 GREASE
NLGI Grade #2
NLGI Service GC-LB
Thickener Non-Soap
Fluid Type Thermally-stable synthetic
Useful Temperature Range -100°F to 500°F
Color Red
Dropping Point, °F 900+
Load Wear Index 71.2
4-Ball Wear Scar Diameter (Red), 40 Kg 0.46 mm
Water Washout @ 105°F 1%
Evaporation Loss, 22 hrs @ 350°F 4%
Oil Separation, 30 hrs @ 350°F 5%
Oxidation Stability, 500 hrs @210°F, psi 12
Rust Test, ASTM D1743 Pass

Red Line CV-2 Grease is designed to withstand the extreme temperatures and pressures
which occur in high-performance wheel bearings and CV-joints. The excellent hightemperature
stability, extreme-pressure protection, and water resistance enables it to
out-perform even the best conventional or synthetic greases. Red Line CV-2 Grease can be
used in a wide range of applications at temperatures ranging between -100°F to 500°F and
provides good oxidation and corrosion resistance, low evaporation and oil separation, and has
a minimum effect on rubber seals. The exceptional extreme-pressure performance and the
fluidity of the synthetic oil allows increases in bearing life of 200% to 800%. Red Line CV-2
Grease contains a red moly compound which is a superior lubricant to black moly disulfide
lubricants.
Red Line CV-2 Grease may also be used in industrial applications such as high-temperature
alternator bearings, high-speed ball bearings, conveyor bearings, worm gear drives, servo
mechanisms, and applications where vibrations can cause fretting wear and corrosion to take
place.
Red Line CV-2 Grease will retain its consistency and extreme-pressure performance under
high-temperature and high-shear conditions for extended periods, which extends the
performance ranges of the lubricated components. Red Line CV-2 will slightly darken after
high-temperature use; this darkening will not detrimentally effect the performance of the
grease. Although Red Line CV-2 is compatible with small amounts of many petroleum-based
greases, it is always good lubrication practice to thoroughly clean out the old grease to
eliminate abrasive particles and to minimize the possibility of grease incompatibility.

*Free USPS Priority Mail shipping for orders over $99 to all US States unless otherwise noted. Delivery times vary between 1-3 business days.

 International (including Canada) shipping is done via USPS unless otherwise noted. Shipping times vary due to customs, but please allow 10-15 business days for delivery.

Please view the following link for more information about shipping, payments and returns:

http://www.t3technique.com/payment-and-return-policies/

*All prices are in U.S Dollars